OLED 2864 display module(.NET Gadgeteer Compatible) 

            <img alt="" src="http://images.ncnynl.com/arduino/2016/500px-OLED2864_1.jpg" width="500" height="332" class="thumbimage" />  <img src="http://images.ncnynl.com/arduino/2016/magnify-clip.png" width="15" height="11" alt="" />OLED 2864 display module(.NET Gadgeteer Compatible) (SKU:TOY0007)

目录

1 概述
2 性能描述
3 引脚定义
4 安装尺寸
5 IIC数据格式及时序图
6 指令表
7 字模数组
8 Arduino平台应用

8.1 硬件连接
8.2 例子程序

概述
OLED 2864 display module是一款无需背光源自发光显示模块。显示颜色有蓝色、黄蓝两种，显示尺寸0.96寸，驱动IC：SSD1306，
该模块通过IIC接口与控制器通信，Arduino、Gadgeteer平台均可用。显示效果好，安装方便。

性能描述
工作电压：3.3V
显示颜色：蓝色、黄蓝
像素个数：128列 × 64行
接口方式：IIC
工作温度：-30℃~+70℃
显示面积：21.744 × 10.864(mm)
模块尺寸：42.00 × 32.00(mm)
模块重量： 15克

引脚定义
引脚定义
连接arduino平台接口：

1、3.3：逻辑电压3.3V
2、G：电源负
3、RST：复位信号输入引脚
4、SDA：IIC数据输入引脚
5、SCL：IIC时钟输入引脚
6、DC：SAO设置引脚

Gadgeteer插座：

PIN1:3.3V
PIN2:5V
PIN3:DC
PIN4:NC
PIN5:NC
PIN6:RST
PIN7:NC
PIN8:SDA
PIN9:SCL
PIN10:G

安装尺寸
安装尺寸
IIC数据格式及时序图
参考SSD1306.pdf文件P19~P21页
SSD1306.pdf

指令表
通过设置指令，可以指定OLED显示的行列地址、显示模式等。详细指令及解释参考SSD1306.pdf文件28~48页。

上述指令表中有一个set memory addressing Mode指令如下：（可参考SSD1306.pdf文件P30页）
A[1:0] = 00b, Horizontal Addressing Mode
A[1:0] = 01b, Vertical Addressing Mode
A[1:0] = 10b, Page Addressing Mode (RESET)
A[1:0] = 11b, Invalid
例子程序中没有设置，即默认选择Page Addressing Mode 模式，详细解释可参考SSD1306.pdf文件P25页、P34页。
共分成8页（page0~page7），每页8行（0~7行），总64行；每行128列（seg0~seg127）。
所以，当选择Page Addressing Mode模式，地址选择PAGE2页、seg3列，写入0xff，则屏幕15~23行的seg3列被点亮，如下图：

OLED2864 4.png
字模数组
下面数组是从网上找到的，宽8(列)*高16(行)的字体库

unsigned char F8X16[][16] =
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0
0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//!1
0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//"2
0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//#3
0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$4
0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//%5
0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//&6
0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//'7
0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//(8
0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//)9
0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//*10
0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+11
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//,12
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//-13
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//.14
0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,///15
0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//016
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//117
0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//218
0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//319
0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//420
0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//521
0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//622
0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//723
0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//824
0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//925
0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//:26
0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//;27
0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//<28
0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//=29
0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//>30
0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//?31
0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@32
0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A33
0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B34
0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C35
0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D36
0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E37
0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F38
0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G39
0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H40
0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I41
0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J42
0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K43
0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L44
0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M45
0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N46
0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O47
0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P48
0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q49
0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R50
0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S51
0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T52
0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U53
0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V54
0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W55
0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X56
0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y57
0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z58
0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[59
0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\60
0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//]61
0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^62
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_63
0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//`64
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a65
0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b66
0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c67
0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d68
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e69
0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f70
0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g71
0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h72
0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i73
0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j74
0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k75
0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l76
0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m77
0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n78
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o79
0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p80
0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q81
0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r82
0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s83
0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t84
0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u85
0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v86
0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w87
0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x88
0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y89
0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z90
0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{91
0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//|92
0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//}93
0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~94
};

其中大写字母A：0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,由这些数据组成 其中前8个数据0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00组成字母A上半部分； 后8个数据0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20组成字母A下半部分。

Arduino平台应用
硬件连接
在这里选择Arduino 328作为控制器举例说明
选用杜邦线（公母头）作为连接线，将模块与328板子连接起来

杜邦线一端插在模块排针，另一端插在328板子，线序如下：

模块 ———— 328板子
3.3 ———— 3V3
G ———— GND
RST ———— 6(数字IO，6脚)
SDA ———— 4(模拟IO，4脚)
SCL ———— 5(模拟IO，5脚)
DC ———— 7(数字IO,7脚)

连接USB线

例子程序
主程序

#include <Wire.h>
#include "image.h"

int UG2864Address = 0x3C;//OLED UG2864器件7位地址
//SDA-AD4,SCL-AD5(Gadgeteer PIN8,PIN9)
//端口设置
int RES = 6;//Gadgeteer PIN6
int DC = 7;//Gadgeteer PIN3

//写命令
void Writec(unsigned char COM)
{
Wire.beginTransmission(UG2864Address);
Wire.send(0x00);
Wire.send(COM);
Wire.endTransmission();
}
//写数据
void Writed(unsigned char DATA)
{
Wire.beginTransmission(UG2864Address);
Wire.send(0x40);
Wire.send(DATA);
Wire.endTransmission();
}
//OLED UG2864初始化
void SSD1306()
{
Writec(0XAE);//display off
Writec(0X00);//set lower column address
Writec(0X10);//set higher column address
Writec(0X40);//set display start line
Writec(0XB0);//set page address
Writec(0X81);//set contract control
Writec(0XCF);// VCC Generated by Internal DC/DC Circuit
Writec(0XA1);//set segment remap column address 127 is mapped to SEG0
Writec(0XA6);//normal / reverse normal display
Writec(0XA8);//multiplex ratio
Writec(0X3F);//1/64
Writec(0XC8);//Com scan direction remapped mode. Scan from COM[N-1] to COM0
Writec(0XD3);//set display offset
Writec(0X00);
Writec(0XD5);//set osc division
Writec(0X80);
Writec(0XD9);//set pre-charge period
Writec(0X11);
Writec(0XDa);//set COM pins
Writec(0X12);
Writec(0X8d);/set charge pump enable/
Writec(0X14);
Writec(0Xdb);//Set VcomH
Writec(0X20);
Writec(0XAF);//display ON
}
//填充函数
void fill(unsigned char dat)
{
unsigned char i,j;

Writec(0x00);//set lower column address
Writec(0x10);//set higher column address
Writec(0xB0);//set page address

for(j=0;j<8;j++)
{
Writec(0xB0+j);//set page address
Writec(0x00);//set lower column address
Writec(0x10);//set higher column address
for(i=0;i<128;i++)
{
Writed(dat);
}
}
}
//显示
void show()
{
unsigned char x,y;
unsigned int j=0;

Writec(0x00);//set lower column address
Writec(0x10);//set higher column address

for(y=0;y&lt;8;y++)
{
    Writec(0xB0+y);//set page address
    Writec(0x00);//set lower column address
    Writec(0x10);//set higher column address
    for(x=0;x&lt;128;x++)
    Writed(show2[j++]);
}

}
void setup()
{
//端口模式设置
pinMode(RES,OUTPUT);//RES
pinMode(DC,OUTPUT);//D/C#

//SAO=0
digitalWrite(DC,LOW);

//IIC初始化
Wire.begin();
}
void loop()
{
//复位
digitalWrite(RES,HIGH); delay(1000);
digitalWrite(RES,LOW); delay(1000);
digitalWrite(RES,HIGH); delay(1000);
//初始化
SSD1306();
fill(0xff);//点亮屏幕
delay(100);
fill(0x00);//清屏
delay(100);

while(1)
{
   show();
}

}

*image.h文件

unsigned char show1[] =
{
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x00,0x00,0x00,0x82,0xFF,0x80,0x00,0x00,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x00,0x00,0xC6,0xA1,0x91,0x89,0x86,0x00,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x00,0x00,0x00,0x82,0xFF,0x80,0x00,0x00,0x00,0x00,0xC6,0xA1,0x91,0x89,0x86,0x00,
0x00,0x00,0x42,0x81,0x89,0x89,0x76,0x00,0x00,0x00,0x10,0x2C,0x22,0xFF,0xA0,0x00,
0x00,0x00,0x4F,0x89,0x89,0x89,0x71,0x00,0x00,0x00,0x42,0x81,0x89,0x89,0x76,0x00,
0x00,0x00,0x03,0x01,0xF9,0x07,0x01,0x00,0x00,0x00,0x76,0x89,0x89,0x89,0x76,0x00,
0x00,0x00,0x0E,0xD1,0x91,0x91,0x7E,0x00,0x00,0x00,0x7E,0x81,0x81,0x81,0x7E,0x00,
0x00,0x00,0x00,0x82,0xFF,0x80,0x00,0x00,0x00,0x00,0xC6,0xA1,0x91,0x89,0x86,0x00,
0x00,0x00,0x42,0x81,0x89,0x89,0x76,0x00,0x00,0x00,0x10,0x2C,0x22,0xFF,0xA0,0x00,
0x00,0x00,0x4F,0x89,0x89,0x89,0x71,0x00,0x00,0x00,0x7E,0x89,0x89,0x8B,0x70,0x00,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x00,0x00,0x10,0x2C,0x22,0xFF,0xA0,0x00,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,
0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,0x55,0xAA,

};
unsigned char show2[] =
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//page0
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x08,0xF8,0x88,0x88,0xE8,0x08,0x00,0x00, //DF上半
0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,//Ro
0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,//bo
0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//t
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//page1
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//DF下半
0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//Ro
0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//bo
0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//t
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//page2
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,//page3
0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,//
0x80,0x88,0xF8,0x00,0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x80,0x80,0x80,0x00,//
0x80,0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x08,0xF8,0x00,0x80,//ro上半
0x80,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x80,0x80,0xE0,//bo
0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,//t.c
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,//om
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//.
0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//page4
0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,0x00,0xc0,0xc0,0x00,0x00,0x0E,0x11,0x20,//
0x20,0x10,0x3F,0x20,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,0x20,0x20,0x3F,0x21,//
0x20,0x00,0x01,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,0x00,0x3F,0x11,0x20,//ro下半
0x20,0x11,0x0E,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,0x00,0x00,0x00,0x1F,//bo
0x20,0x20,0x00,0x00,0x00,0xc0,0xc0,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//t.c
0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//om
0x00,0x00,0xc0,0xc0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//.
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//page5
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//page6
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,//cn
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//page7
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//cn
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
};

下载上述程序到Arduino328中，OLED2864上即可显示出www.dfrobot.com.cn。

Nextredirectltr.png购买 OLED 2864 显示模块

标签: Arduino传感器