Arduino内置教程-数字-侦察状态改变

监测按钮的状态变化（边沿监测）

如果你让按键工作，你经常会想做一些要按下很多次按钮的才有响应的动作。这时你需要知道按钮的从闭合到断开的变化状态，然后记录这个状态发生了多少次。这叫状态变化检测或者边沿检测。在这个教程里我们学习怎样检查状态变化，然后我们把相关信息发送到串口监视器里，并记录4次LED灯的开和关。

硬件要求

  • Arduino or Genuino 开发板
  • 即时按钮或者开关
  • 10k ohm 电阻
  • 连接线
  • 面包板

电路

请输入图片描述

  • 连接3根线到开发板。最开始两根，红和黑，连接到面包板上的两个长垂直行来提供5V电源电压和地。第三根线从数字引脚pin2连接到按钮的一个引脚。按钮的同一个引脚连接下拉电阻（10k ohm）到地。按钮的另一个引脚连接到5V电源。

  • 按钮或者开关连接电路的两点。按钮是断开的（未按），按钮两个引脚是没有接通的，所以这个引脚连接到地（通过一个下拉电阻），读取为低电平或者0。当如果按钮是闭合的（未按），按钮两个引脚是接通的，所以这个引脚连接到5V，读取为高电平，或者1。

  • 如果你没有连接到数字I/O口到任何地方，LED灯可能会不规则闪烁。这是因为输入引脚处于悬浮状态——它没有固定连接到电源或者地，并且它会随机在高电平和低电平之间切换。这是你需要下拉电阻的原因。

原理图

请输入图片描述

样例代码

下面的代码连续读取按钮的状态。然后通过循环来对比这个按钮的状态和它上一段时间的状态。如果当前按键的状态和之前的状态不一样并且当前状态是高电平，那么这个按键刚从关变为开。然后程序增加按键按下的计数器。

这个程序也检查按键按下次数的值，并且如果它是4的倍数，它会打开pin13的LED灯，否则这个LED灯饰熄灭的。

/*
  State change detection (edge detection)

 Often, you don't need to know the state of a digital input all the time,
 but you just need to know when the input changes from one state to another.
 For example, you want to know when a button goes from OFF to ON.  This is called
 state change detection, or edge detection.

 This example shows how to detect when a button or button changes from off to on
 and on to off.

 The circuit:
 * pushbutton attached to pin 2 from +5V
 * 10K resistor attached to pin 2 from ground
 * LED attached from pin 13 to ground (or use the built-in LED on
   most Arduino boards)

 created  27 Sep 2005
 modified 30 Aug 2011
 by Tom Igoe

This example code is in the public domain.

 http://www.arduino.cc/en/Tutorial/ButtonStateChange

 */

// this constant won't change:
const int  buttonPin = 2;    // the pin that the pushbutton is attached to
const int ledPin = 13;       // the pin that the LED is attached to

// Variables will change:
int buttonPushCounter = 0;   // counter for the number of button presses
int buttonState = 0;         // current state of the button
int lastButtonState = 0;     // previous state of the button

void setup() {
  // initialize the button pin as a input:
  pinMode(buttonPin, INPUT);
  // initialize the LED as an output:
  pinMode(ledPin, OUTPUT);
  // initialize serial communication:
  Serial.begin(9600);
}


void loop() {
  // read the pushbutton input pin:
  buttonState = digitalRead(buttonPin);

  // compare the buttonState to its previous state
  if (buttonState != lastButtonState) {
    // if the state has changed, increment the counter
    if (buttonState == HIGH) {
      // if the current state is HIGH then the button
      // wend from off to on:
      buttonPushCounter++;
      Serial.println("on");
      Serial.print("number of button pushes:  ");
      Serial.println(buttonPushCounter);
    } else {
      // if the current state is LOW then the button
      // wend from on to off:
      Serial.println("off");
    }
    // Delay a little bit to avoid bouncing
    delay(50);
  }
  // save the current state as the last state,
  //for next time through the loop
  lastButtonState = buttonState;


  // turns on the LED every four button pushes by
  // checking the modulo of the button push counter.
  // the modulo function gives you the remainder of
  // the division of two numbers:
  if (buttonPushCounter % 4 == 0) {
    digitalWrite(ledPin, HIGH);
  } else {
    digitalWrite(ledPin, LOW);
  }

}

[Get Code]

更多

  • pinMode()
  • digitalWrite()
  • digitalRead()
  • millis()
  • if
  • BlinkWithoutDelay - 不用delay（）函数，使LED灯闪烁
  • Button - 用一个按钮来控制LED灯
  • Debounce - 读取一个按钮，并滤掉噪音
  • DigitalInputPullup - 示范怎么用pinMode（）来上拉引脚
  • toneKeyboard - 一个用压力传感器和压电扬声器的三键音乐键盘
  • toneMelody - 用压电扬声器弹奏一个旋律
  • toneMultiple - 用tone（）命令在多个扬声器上发音
  • tonePitchFollower - 用模拟输入在压电扬声器上弹奏高音

标签: arduino内置教程, arduino侦察状态改变